Skip to content

3.3 Keeping thermochemical corrections and standard states consistent

These are unexecuted teaching inputs and starting models. Original diagrams are schematics, not calculated results. Validate version-specific syntax, licensed or authorized data, numerical convergence and the scientific model before using this workflow.

3.3.1 Model, units and provenance

Geometry in Å; electronic energy in hartree; vibrational wavenumbers in cm⁻¹. Check each printed field and keep thermal and standard-state terms distinct.

Shared inputs, conventions and evidence

Original schematic: Keeping thermochemical corrections and standard states consistent. No numerical results are claimed.
Original schematic: Keeping thermochemical corrections and standard states consistent. No numerical results are claimed.

3.3.2 Unexecuted inputs and explicit deltas

Use the accompanying instructions to identify the parent calculation and placement of every delta; a snippet is not automatically a standalone input. Preserve all blank-line and file-provenance requirements.

3.3.2.1 Input block 1

%oldchk=case10_water_min.chk
%chk=case11_water_298.chk
%mem=4GB
%nprocshared=2
#p B3LYP/6-31G(d) Freq=ReadFC Geom=AllCheck Guess=Read
   Temperature=298.15 Pressure=1.0

3.3.2.2 Input block 2

%oldchk=case10_water_min.chk
%chk=case11_water_350.chk
%mem=4GB
%nprocshared=2
#p B3LYP/6-31G(d) Freq=ReadFC Geom=AllCheck Guess=Read
   Temperature=350.0 Pressure=1.0

3.3.3 Worked investigation

3.3.3.1 Question and intuition

Why do electronic energy, zero-point-corrected energy, enthalpy, and Gibbs energy differ for the same optimized molecule? Electronic energy is one part of the bookkeeping. Nuclear zero-point motion and temperature-dependent rotational, translational, and vibrational terms add further contributions. Gibbs energy also contains the entropy term. Think of several carefully labeled totals in a ledger: each total contains different entries, so adding two totals can count some entries twice. This case uses the validated water minimum from Case 10 to learn that accounting without introducing a chemical reaction.

Prerequisite: case10_water_min.chk must contain the completed same-level frequency calculation, not merely an SCF wavefunction or an optimization checkpoint with an approximate Hessian. Reusing the computed Hessian changes the statistical-mechanical analysis conditions without recomputing the electronic potential-energy surface. Changing the temperature keyword does not perform molecular dynamics, introduce a liquid, or optimize a finite-temperature free-energy surface.

3.3.3.2 Checkpoint based inputs

Run the two inputs separately. Each copies the verified source into a different output checkpoint. With Geom=AllCheck, omit the title, charge/multiplicity, and coordinate sections entirely; a blank line terminates the route section. The source remains available for future cases.

See input block 1 above.

See input block 2 above.

3.3.3.3 Workflow

  1. Confirm the source minimum has no imaginary internal modes. Read the mass/isotope information and rotational symmetry number from the original output; these affect thermochemistry even if the electronic energy is unchanged.
  2. Run both analyses and verify the printed temperature in kelvin and pressure in atmospheres. Do not assume that an input file was parsed correctly simply because its name includes “350K”.
  3. Transcribe Eelec, the zero-point correction, thermal corrections to energy/enthalpy/Gibbs energy, and the corresponding sums. Retain full precision until taking differences. Most correction and sum lines are in hartree; entropy in the thermochemistry table is commonly cal mol−1 K−1, so read the table header rather than guessing.
  4. Reconstruct H = Eelec + Hcorr and G = Eelec + Gcorr, then check G = H − TS after converting units. The listed thermal corrections already include zero-point energy; do not add the zero-point correction a second time.
  5. Compare the two temperatures. With an unchanged geometry and Hessian, changes come from the thermochemical treatment. Record the exact temperature, pressure, isotopes, symmetry convention, and scaling convention beside every reported G value.

3.3.3.4 Standard state audit

Gaussian's ordinary frequency thermochemistry is an ideal-gas RRHO treatment, with defaults of 298.15 K and 1 atm. A solution calculation elsewhere in a project does not automatically replace the translational partition function by a liquid-state model. If the chosen thermodynamic cycle requires converting an ideal-gas 1 atm standard chemical potential to a 1 mol L−1 standard chemical potential, the per-species correction is ΔG° = RT ln(C°RT/p°), with units inside the logarithm made dimensionless. At 298.15 K this is approximately +7.93 kJ mol−1. This number is a standard-state conversion derived from constants, not a Gaussian molecular result.

For a balanced reaction, the net conversion is Δν RT ln(C°RT/p°), where Δν is the sum of product stoichiometric coefficients minus the reactant sum for the species being converted. A one-molecule-to-one-molecule isomerization has cancellation; an association does not. Do not add this correction automatically to a solvation free energy already defined for the target standard states. Write down the gas and solution reference states on both sides of the thermodynamic cycle first. Also distinguish 1 atm from 1 bar if the experimental reference uses the latter.

3.3.3.5 Checks pitfalls and exercise

Acceptance requires successful reconstruction of the reported sums and an explicit standard-state statement. Frequent errors are combining a 350 K enthalpy with a 298 K entropy, mixing calories and joules, calling a thermal correction the total energy, or interpreting the molecular Gibbs energy as a standard Gibbs energy of formation from the elements. Low-frequency torsions can make RRHO entropy unreliable; water avoids most of that complexity but does not make the approximation exact.

EN exercise: Derive the sign of the 1 atm→1 M correction from μ = μ° + RT ln a, and predict its net sign for A+B→AB. Then explain why the same correction cancels for the ammonia inversion used in Cases 14–16. No molecular energy values need to be invented to answer either question.

3.3.5 Sources and further reading